Hoppa till innehåll
Free shipping on orders over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%How to Know Your Original Gravity Without Waiting for the Wort to CoolA Few Drops of Milk Are Enough to Tell Whether the Calf Gets the Right StartThe True Sugar Content of Wort and the Freezing Point of Glycol Can Be Measured with the Same InstrumentWhy a standard Brix refractometer shows the wrong sugar content in wortWhy Many Salinity Meters Give Wrong Readings: Seawater Is More Than Sodium ChlorideBath concentration determined in seconds with two drops and the press of a buttonSame sample, different temperature, different result: how to get a Brix value you can trustSame sample, three readings: how to get a Brix value that doesn’t depend on who is lookingThree Seconds and One Number: Brix Measurement Without Interpreting a Boundary LineThe same refractometer checks the sugar content in juice and the concentration in coolantVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%How to Know Your Original Gravity Without Waiting for the Wort to CoolA Few Drops of Milk Are Enough to Tell Whether the Calf Gets the Right StartThe True Sugar Content of Wort and the Freezing Point of Glycol Can Be Measured with the Same InstrumentWhy a standard Brix refractometer shows the wrong sugar content in wortWhy Many Salinity Meters Give Wrong Readings: Seawater Is More Than Sodium ChlorideBath concentration determined in seconds with two drops and the press of a buttonSame sample, different temperature, different result: how to get a Brix value you can trustSame sample, three readings: how to get a Brix value that doesn’t depend on who is lookingThree Seconds and One Number: Brix Measurement Without Interpreting a Boundary LineThe same refractometer checks the sugar content in juice and the concentration in coolant

IRIS inline refractometer — the spot check reveals what the concentration was in that exact cup, at that exact moment

Published August 20, 2026 at 08:51

The routine is familiar: an operator draws off a sample, walks to the bench, drops a few drops onto the prism and takes a reading. The value is logged, and the batch is approved. But what was just documented was the concentration in that cup, at that moment. What happened during the three hours between two samples — when the dilution water ran a little too long, when a pump cavitated, when a tank was topped up — nobody knows. Spot checks measure points. The process is a curve.

IRIS intelligent inline refractometer, process sensor mounted directly in the flow

What it is

IRIS is an inline refractometer that mounts directly in the process flow and measures the concentration continuously in the liquid passing through. Unlike conventional process refractometers, it is a true smart sensor: all the electronics and all the computation sit inside the sensor itself, which operates completely independently of an external controller. It connects directly to the control system via an analog output of 4–20 mA or 0–10 V, with digital RS232 as an option.

The problem it solves

The first problem is time resolution. A measurement taken continuously catches the deviation while it’s happening and can trigger an alarm or control action directly — dilution, dosing, valve position. A spot sample every three hours can, at best, tell you that something went wrong at some point during those three hours, by which time the batch has already been produced.

The second problem is architecture, and this is where IRIS differs from most. Traditional inline refractometers are, in practice, ”dumb sensors” cable-connected to an external control cabinet. The cabinet carries the display, the user interface, and the connections onward to the PLC or data acquisition system. That costs money, takes up space near the process, lengthens the installation — and becomes yet another thing to maintain and that can break down. In addition, the dumb sensor usually sits in the main flow and requires special, often expensive, adapters.

That model is a legacy from a time when someone actually stood and looked at a display in the cabinet. Today almost no one reads the value there — you want the sensor on your network and the figure in the PLC, HMI, or SCADA. By putting the intelligence in the sensor, the middleman disappears: a two-wire connection into the control system that’s already there, and if a local display is needed, a simple standard meter can be used instead of a proprietary cabinet.

The fact that it measures refractive index is the very foundation. The refraction of light in the liquid is a direct physical function of the concentration of dissolved substances — no consumables, no reagents, no electrode that ages. The sensor has no moving parts in the medium, which is exactly what a process that needs to run around the clock requires.

Three typical use cases

  • Food and beverage: continuous Brix monitoring during evaporation, blending, and dilution, where the recipe must stay within tight limits throughout the batch.
  • Chemical processing and cleaning: concentration in caustic, acid, and CIP solutions — where too weak means the cleaning doesn’t work and too strong means unnecessary chemical consumption.
  • Cutting fluid and industrial fluid systems: central systems where the concentration drifts slowly with evaporation and refilling, and where the deviation shows up in tool life long before anyone takes a sample.

Why it pays off

Do the math on the batch, not on the instrument. An incorrect concentration discovered at the next spot check has already had time to produce everything in between — and that volume must either be adjusted, reblended, or discarded. The longer the interval between samples, the greater the volume at stake every time something drifts.

Add to that what disappears from the calculation: the control cabinet, the cabling to it, the adapter in the process pipe, the installation hours, and the maintenance of an extra cabinet. And add the labor time for the sampling round itself — it recurs every shift, every day, year-round, and still provides a weaker basis than a sensor that measures continuously. The real gain, however, is the one that doesn’t show up on any invoice: a process that can be controlled based on a measured value instead of merely being checked after the fact.

Read more about the IRIS intelligent inline refractometer →

More news

All news